Specifications |
CHARACTERISTICS
Carrier : Tracks mounted |
Drilling techniques : Blast Hole |
Drilling applications : Blasting, construction |
Weight and Dimensions
Lenght:........13.05 m <> 42’ - 10” |
Width:............2.89 m <> 9’ - 6” |
Height:...........3.55 m <> 11’- 66” |
Approx. weight:......33792kg <> 74500lbs |
Mobile-Undercarriage High-Trac
Tracks mounted steel shoes |
Track length: 4.26m <> 14.0’ |
Triple grouser shoes width: 457mm <> 18” |
Pressure applied brake system |
Traction effort: 24947 kg <> 55,000lbs |
Grade ability: 27° <> 52% (Engine max. 20°<> 36%) |
Ground clearance: 381mm <> 15” |
Independent tracks oscillation (±8°) |
Frame specifically designed for rough drilling conditions |
Travel speed: max. 4.8km/h <> 3.0mph |
Power Unit
Electronic diesel engine QSK-19 ECM control (24 volts) |
Power: 700hp @ 1800rpm |
Operational fuel consumption: 74.87L/hr <> 19.78gall/hr |
Fuel tank 1136L. <> 300galls |
Filtering system two stage (Primary @ security) |
Emission certification: U.S. EPA Tier 3, CARB Tier 3, EU Stage IIIA |
Integrated control safety panel, 24 volts |
Compressor unit (Dual performance)
Compressor (Sullair) |
Heavy Duty, Energy efficient 1025cfm x 500psi x 1800rpm |
Heavy Duty, Energy efficient 1165cfm x 350psi x 2100rpm |
Type: Two stage oil floated screw air |
Rating condition: Sea level & 20° C |
Cooling: Air cooled radiator, charge-air, oil cooler |
Intake modulation: Full range control for partial load |
Intake filters: Two stage dry type |
Controls: Pressure gauge, temperature gauge, air filter
maintenance indicator |
Compressor Safety device
High discharge temperature |
High receiver pressure |
High Inter stage temperature |
High Inter stage pressure |
Low oil pressure |
Minimum pressure valve |
Pressure relive valve |
Hydraulic power unit & components
Pump drive: Two (2) variable displacement piston pumps, load sensing, pressure
compensated, and one (1) piston pump dedicated for dust collector. |
Hydraulic tank capacity 432 L. <> 114 gall. |
Hydraulic oil cooler |
Filtration system (5 micron) |
Body valves assembly for complete controls (Tram, positioning and drilling) |
Fittings and adapter type «OSFS & ORB» |
Hydraulic hoses standard heavy duty |
Air system supply «Dual mode 500psi & 350psi» |
Automatic lubricator for the down the hole hammer |
Automatic thread grease |
Floating spindle, saving sub, bit basket |
Camera infra-red vision 1 front /2 rear |
Integrated safety system (Over heat, low level etc…) |
Boom positioning
Boom: single section |
Boom: swing: (30°/10°) |
Tilt inclination: (15° below, 45° above the horizontal) |
Dump: (±45° under, ±75° above from the vertical) |
Oscillation: Left/ Right (-20° to +50° from the vertical pin #1) |
Oscillation: Left/Right (+50° to -6° from the horizontal pin #2) |
All hydraulic cylinders are equipped with integrated safety locks |
Mast & Feed Assembly
Mast structure HD designed |
Feed system hoisting and pull down power is provided by linkchain that use a hydraulic powered gear box controlled hydraulically for accurate trus |
Pull down force: 17500lbs <> - 77.8Kn |
Pull back capacity: 17500lbs <> 77.8Kn |
Rotary head mounting plate is equipped with urethane antiwear plates |
Wireless Jib winch operation capacity: 1200 lbs <> 544 kg |
Drill Head
Rotary drive head: Euro-drill RH900 |
Torque capacity type motor 95: 5015lbf-ft <> 6800Nm |
Rotation speed: 0 – 100rpm |
Working pressure: 3600psi |
Torque capacity type motor 98: 8113lbf-ft <> 11000Nm |
Rotation speed: 0 – 86rpm |
Working pressure: 3000psi |
Automatic constant rotation power control |
Swivel passage 50.8 mm <> 2” |
Drive flange |
Drilling table: Break-out
Swivel break-out retractable jaws (Swing torque 22436lb-ft) |
Clamps retractable jaws (Clamps hold force 58560lb-ft) |
Hydraulic « Centralizer» |
Hydraulic adjustable skirt deflector |
Max. opening of 222 mm <> 8¾’’ |
Carrousel – Standard
Carousel of (6+1) rods 20’ long <> 6.00m) |
Stars «set» for 3½” to 5” dia. rods (Option) |
*Note: only one set is included in the base price unit, pipes not included |
Gate for loading pipe in horizontal position |
Water Injection Pump
Model FMC L04 |
Double piston pump, Complete filtering system |
Volume; 34 L/min <> 9 gal/min |
Pressure: 38 bar <> 550 psig |
Revolution speed: 500 rpm |
Water tank «Stainless steel»: 1136 L/h <> 300 gall/h |
Noise less cab «ROPS»
Fully thermal (Summer-Winter) |
Vibration isolated seat and seat belt |
Sound insulation environment less than 85 dBa |
All function are controlled from cab |
Panel view: Display all pressure/ shutdown alarm/ active controls/ meters |
All glass is safety glass |
Windshield double wiper |
Working light for extended hour |
Cab control panel (Joy sticks Hall effect CAN bus)
2 friendly Joysticks, full operational control |
Process and dialogue module, 7” color display, “IFM” |
Rotary and Joystick knob for display function reading “Grayhill” |
CAN-bus keypads readings |
“Air flow” tests results (Ext. temp.-30°)
Engine set-up at 1900rpm/500psi_Air-end flow 1200scfm @ 401psi. |
Engine set-up at 2000rpm/350psi_Air-end flow 1300scfm @ 348psi. |
Engine set-up at 2000rpm/500psi_Air-end flow 1350scfm @ 474psi. |
Present reading theoretically fuel consumption drilling with factor 66% [65.09 L/HR_US gall 17.19 gall/HR] |
Optional Equipment
Rear stabilizer |
High pressure filter to pump |
Angle & Dept indicator |
Winter heating package (Engine/Comp .receiver/Hyd & Water tank/Battery) |
Air grease gun |
Drill pipe size conversion kit |
Hydraulic winch 45000lbs <>20412 kg |
Dust collector HLM900 for 6½” hole |
Dust collector HXL900 for 8½” hole |
Shipping
Overseas packaging: 40 ft container |
Inland shipment: Flatbed |
* Some of the features are optional
** Subject to ground conditions, compressor or water / mud pump capabilities, type and a quality of drilling equipments used and driller skills |
|