Blast Hole Drilling Rigs Comparison Charts

Rockmaster 615 versus - CUBEX QXR 920
  - Tamrock Titon 600 / Sandvik DI600
  - Atlas Copco ROC L7


Specifications Data
Rockmaster 615-Ecc (Electric) Rockmaster 615-Dcc (DIESEL) CUBEX QXR 920 Tamrock Titon 600 / Sandvik DI600 Atlas Copco ROC L7
Metric<>US Metric<>US Metric<>US Metric<>US Metric<>US
Undercarriage Track length 4100 mm <> 13.48 ft 4100 mm <> 13.48 ft n/s* n/s n/s
Max. width 2413 mm <> 7,9 ft 2413 mm <> 7,9 ft n/s n/s n/s
Pad width 381 mm <> 1.25 ft 381 mm <> 1.25 ft 500 mm <> 1.64 ft n/s n/s
Climbing ability 19° <> 35% 19° <> 35% 19° <> 35% n/s 19° <> 35%
Max. speed 4.4 km/h <> 2.6 mph 4.4 km/h <> 2.6 mph 7 km/h <> 4.4 mph 3.5 km/h <> 2.2 mph 3.5 km/h <> 2.2 mph
Track oscillation +10 º/ - 10 º +10 º/ - 10 º +10 º/ - 10 º n/s +10 º/ - 8 º
Ground clearance 381 mm <> 1.25 ft 381 mm <> 1.25 ft 406 mm <> 1.33 ft n/s 405 mm <> 1.33 ft
Rear stabilizer 1 1 n/s n/s n/s
Power pack DIESEL Engine x Cummins CAT 3406E (C15) CAT C15 Acert CAT C13
Output power x 515 kw <> 700 hp / 1800 rpm 375.8 kw <> 500 hp / 1800 rpm 403 kw <> 540 hp / 1800 rpm 328 kw <> 417 hp / 1800 rpm
Operational fuel consumption x 109 L/hr <> 28.2 gall/hr n/s n/s n/s
Emission certification x U.S. EPA Tier 3, EU Stage III n/s n/s n/s
Integrated control safety panel x Over heat / law level / Etc.. n/s n/s n/s
Fuel tank x 1200 L <> 317 Gal n/s n/s 760 L <> 201 gal
Main pump x 340 L/min <> 90 gal/min n/s n/s n/s
Oil tank x 340 L <> 90gal 416 L <> 110gal n/s n/s
Power pack ELECTRIC Motor Electric GE / Westinghouse x x x x
Output power 500 kw <> 680 hp / 1800 rpm x x x x
380 volts / 3 phase / 50 cycle x x x x
Ground fault protection above circuit 110VAC x x x x
Proven safety system GE / Westinghouse x x x x
Integrated control safety panel Over heat / law level / Etc.. x x x x
Main pump 340 L/min <> 90 gal/min x x x x
Oil tank 340 L <> 90gal x x x x
Boom Positioning Swing Left & Right 30° / 30° 30° / 30° 30° left / 35° right n/s n/s
Extention 910 mm <> 3 ft 910 mm <> 3 ft n/s n/s n/s
Inclination from horizontal 15° under- 45° above 15° under- 45° above n/s n/s n/s
Dump from vertical 45 under - 75° above 45 under - 75° above n/s n/s n/s
Oscillation Left & Right 30° to 30° pin #1- 30° to 105° pin #2 30° to 30° pin #1- 30° to 105° pin #2 30° to 30° n/s n/s
Feed Mast Feed stroke 5490 mm <> 18 ft 5490 mm <> 18 ft 7.32 m <> 24 ft n/s 7.50 m <> 25 ft
Total length 7620 mm <> 25 ft 7620 mm <> 25 ft 8.87 m <> 32.7 ft n/s 11.40 m <> 37 ft
Max. length (Rod) 4570 mm <> 15 ft 4570 mm <> 15 ft 6000 mm <> 20 ft 6000 mm <> 20 ft n/s
Carousel capacity 31500 mm <> 103.3 ft (6 +1 rods) 31500 mm <> 103.3 ft (6 +1 rods) 42700 mm <> 140 ft 42000 mm <> 138 ft 36000 mm <> 120 ft
Feed force (Pull down) 66,7 KN <> 17000 lbs 66,7 KN <> 17000 lbs n/s n/s 40 KN <> 8992 lbs
Retrac force (Pull back) 66,7 KN <> 17000 lbs 66,7 KN <> 17000 lbs n/s n/s 50 KN <> 11240 lbs
Rotary Head Hydraulic motors 2 2 n/s n/s n/s
Max. torque 8135 Nm / 209,9bar<> 6000 lbf-ft/3000psi 8135 Nm / 209,9bar<> 6000 lbf-ft/3000psi 5730 Nm / 209,9bar <> 4225 lbf-ft/3000psi 4000 Nm 3030 Nm / 209,9bar<> 2235 lbf-ft/3000psi
Max speed 0 to 80 rpm 0 to 80 rpm 0 to 80 rpm 0 to 100 rpm 0 to 256 rpm
Spindle thread 3½" API REG 3½" API REG n/s n/s n/s
Swivel passage 1½" 1½" n/s n/s n/s
Break-out & Clamps Min. handling 70 mm <> 2¾ in 70 mm <> 2¾ in n/s 110 mm <> 4 1/2 in 89 mm <> 3 1/2 in
Max. handling 222 mm <> 8¾ in 222 mm <> 8¾ in n/s 190 mm <> 7 1/2 in 127 mm <> 5 in
Breaking torque 19964 Nm <> 14725 lbs 19964 Nm <> 14725 lbs n/s n/s n/s
Pipe sliding climbing clamp force 200 KN <> 45000 lbs 200 KN <> 45000 lbs n/s n/s n/s
Hydraulic drilling guide clamp Centralizer Centralizer Centralizer n/s n/s
Compressor Make Sullair / Ingersol Rand Sullair / Ingersol Rand Sullair n/s n/s
Model 29-34 GSD 29-34 GSD n/s n/s n/s
Oil floated two stage two stage n/s n/s n/s
Volume & Pressure 29 cu.m x 34,4 bar / 36,8 cu.m x 24 bar 29 cu.m x 34,4 bar / 36,8 cu.m x 24 bar 25.5 cu.m x 34,4 bar / 29.73 cu.m x 24 bar 28.0 cu.m x 24 bar n/s
Volume & Pressure 1025 cfm x 500 psi / 1300 cfm x 350 psi 1025 cfm x 500 psi / 1300 cfm x 350 psi 900 cfm x 500 psi / 1050 cfm x 350 psi 999 cfm x 350 psi 540 cfm x 171 psi
Control safety panel Integrated Integrated Integrated n/s n/s
Water Pump Model FMC L09 FMC L09 n/s n/s n/s
Water pump 109 L/min <> 28,9 gal/min 109 L/min <> 28,9 gal/min n/s n/s n/s
Pressure 48 bar <> 700 psi 48 bar <> 700 psi n/s n/s n/s
Revolution speed 890 rpm 890 rpm n/s n/s n/s
Water tank "Stainless steel" 454 L <> 120 gall "Stainless steel" 454 L <> 120 gall n/s n/s n/s
Winter anti freeze tank 19 L <> 5 gall 19 L <> 5 gall n/s n/s n/s
Winch Jib Max. line pull 544 kg <> 1200 lbs 544 kg <> 1200 lbs n/s n/s n/s
Drum capacity 2650 mm <> 87 ft 26,5 m <> 87 ft n/s n/s n/s
Rope speed 0-28 m/min <> 0-88 ft/min 0-28 m/min <> 0-88 ft/min n/s n/s n/s
Rope diameter 6 mm <> ¼" 6 mm <> ¼" n/s n/s n/s
Dimension Length 12020 mm <> 39.50 ft 9700 mm <> 31.83 ft 11278 mm <> 37.00 ft 12700 mm <> 41.84 ft 11500 mm <> 39.30 ft
Width 2400 mm <> 7.90 ft 2450 mm <> 8.00 ft 3000 mm <> 9.80 ft 2500 mm <> 8.25 ft 2500 mm <> 8.10 ft
Height 3560 mm <> 11.66 ft 3560 mm <> 11.66 ft 3500 mm <> 11.48 ft 3300 mm <> 10.84 ft 3500 mm <> 11.60 ft
Weight 25 000 kg <> 55114 lbs 26 762 kg <> 59000 lbs 27 215 kg <> 60000 lbs 29 000 kg <> 63934 lbs 23 700 kg <> 52250 lbs
Optional Equipment Noiceless, conrtable and ergomic cab Noise less thermal cab Caterpillar Noise less thermal cab Caterpillar n/s n/s n/s
Electric wire cable v x x x x
Carousel drill size set v v n/s n/s n/s
Winter condition sytem v v n/s n/s n/s

* data not specified

* Source: websites and/or printed catalogues, available from respective drilling equipment manufacturers